Rev 1/2 vs rev 3 filter volume

[echoloch]

Hey,

I noticed my rev 1/2 filter setting isn't as loud as when I set it to rev 3. The 1/2 seems approximately -3dB volume..

Is anyone else experiencing this? 

I hope nothing is wrong with mine. 

Cheers,
echoloch

[S_A_P]

I dont know if I would say the difference is volume related as much as the Rev 3 is brighter while the Rev 1/2 is more of a darker tone. I guess it would depend on where you hear the 3db difference?

[echoloch]

I dont know if I would say the difference is volume related as much as the Rev 3 is brighter while the Rev 1/2 is more of a darker tone. I guess it would depend on where you hear the 3db difference?

It is not only noticeable by ear but I can see it on my interface input volume.

I guess I could post a sample on soundcloud.

EDIT: sample https://soundcloud.com/echoloch/rev1-23

[LPF83]

Have you already patched the OS to 1.2.0?   

If so and it's still doing this, I would send support a note.  I don't get a volume difference like that between the two filters.

I find the difference heard on each filter type depends largely on the type of sound, but to me the Rev 1/2 filter tends to sound a little brighter due to the more linear nature of the envelope.  The Rev 3 filter is more logarithmic than linear, which rounds off the high frequencies more abruptly, rather than filtering on a more gradual slope.

[echoloch]

Have you already patched the OS to 1.2.0?   

If so and it's still doing this, I would send support a note.  I don't get a volume difference like that between the two filters.

I find the difference heard on each filter type depends largely on the type of sound, but to me the Rev 1/2 filter tends to sound a little brighter due to the more linear nature of the envelope.  The Rev 3 filter is more logarithmic than linear, which rounds off the high frequencies more abruptly, rather than filtering on a more gradual slope.

Yes, I updated the OS as soon as I received mine. I used MIDI-OX and it went smoothly as far as I could tell...

Maybe I should try to update it again before I shoot Andy a message?

Anyways, thanks you two for the input!

cheers,
echoloch

[Flux302]

I've found the same... I am not sure but i think it may have been improved a bit between pre 1.2 and post 1.2. It was jarring before now It sounds more like a difference in filters as opposed to a massive drop off. I would be surprised if there wasn't a change in 1.2 that had addressed that and I am just not noticing it as much now. .... I almost wanna downgrade to double check my mind set to be sure I am not talking out my booty.

[echoloch]

I've found the same... I am not sure but i think it may have been improved a bit between pre 1.2 and post 1.2. It was jarring before now It sounds more like a difference in filters as opposed to a massive drop off. I would be surprised if there wasn't a change in 1.2 that had addressed that and I am just not noticing it as much now. .... I almost wanna downgrade to double check my mind set to be sure I am not talking out my booty.

After toggling between filters with the presets I've concluded there is nothing wrong with mine. It seems the volume difference is dependent on the particular sound/ patch you are going for. I love how you get both filters.. it really gives the rev 4 this ying yang, dark side, light side vibe. 

[amk21093]

I've updated to 1.5 from 1.2 and this problem has ceased, though it wasn't mentioned in the patch notes. It was a  very pronounced issue for my P10 before.

[kyps]

Hi guys,
I just got my p10, I just have a question,

Is that normal that when you make an unit patch you can have a « higher »sound about the filter when you turn on the « enveloppe amount » ?

Is that normal ?

Thanks

[NewProphet]

Hi guys,
I just got my p10, I just have a question,

Is that normal that when you make an unit patch you can have a « higher »sound about the filter when you turn on the « enveloppe amount » ?

Is that normal ?

Thanks

Yes, that’s totally normal.

[LPF83]

Hi guys,
I just got my p10, I just have a question,

Is that normal that when you make an unit patch you can have a « higher »sound about the filter when you turn on the « enveloppe amount » ?

Is that normal ?

Thanks

Yes, that’s totally normal.

It's a bit different than most other synths, which seem to generally init patch with filter wide open.  I assume it's because the original P5 had this characteristics.